The above is coming along
A new ISS SSTV event is on, was scheduled to begin tomorrow but already broadcasting today and scheduled to continue nonstop until the 8th!
145.8 mhz at 22050 (or 22) khz bandwidth in PD120 mode
RXSSTV and MMSSTV are freeware for decoding
Robot36 in android playstore used to be free at least not sure if it still is
CQ SSTV on apple is $3
145.8 is amatuer band and its a pretty strong signal and there are a number of different ways to do it! Will update with captures
(If you’re using sdr# and the aforementioned decoders, the settings Im using are NFM, 1.024 msps sample rate, broad or no BPF on Hilbert TF demod, post rx manual slant correction)
I’ll upload as many good wav recordings as I can
Heres todays

Update 10-4 transmission ceased due to to approaching cygnus rendezvous with new space toilet
https://www.nasa.gov/nasalive
But before it broke I got these



The trick is synching the clocks or to multiples, sdr# uses a default 48khz audio output, can’t change it so the decoder clock needs changed from 11025 (pretty close to 12) to 12, 24 or 48khz, thats how its a little crisper image than before (there was no way to make out that small text on the other images from new years)


(Look at all those cameras!)

Ok, the GTmedia V7plus DVBS2T2 tuner on th 5 el yagi at 437 I made for dsd. Initial attempt was no good although the signal on the analyzer (sdr#)looked decent.
So I emailed the ham who runs the channel and he said this box is used by amatuers for this purpose. So I got with the ham guy (Jim), he’s an older fella but he’s been doing ATV for 45 years, currently hes working with a 5.8. Ghz digital broadcast setup, his ham antenna outside looks a big inverted umbrella frame it was neat.
Anyways he said no it doesn’t work and referenced a specific, different although similiar box that they used for this and they stopped working because of the new firmware disallowing tuning to those frequencies and further disllowing downgrading the firmware (though theres sometimes ways around that).
So, not easily discouraged I tried turning the antenna vertically polarized and it picks up strong, intermittent signal blips 1-2 seconds, so I’ll put it higher and try again this week.
I’m not sure if I mentiond but I built a .64 λ monopole for 27mhz, its 7.1 meters (about 23’) long up in a dead tree (which my landlord wants to chop in December of all months so a limited time opprotunity) with seven 9’ ground radials for cb. It worked fine for that, just truckers really but my radio isn’t the best (turns out its a FCCd version of a blackbox that can tune from like 23 to 31 mhz though I have yet to open it up an see about it) so I hooked it up to the RTL SDR for SSTV on 14.23 mhz which comes in pretty well sometimes. Its just like the ISS bit but terrestrial, from hams and send pictures with signal reports back and forth like how they would speak. The signals they broadcast are usually through directional antennae and, on this frequency in the 20 meter band, are affected by ionospheric conditions a lot and usually only come in during the daytime. Some transmit QRP which means reduced power as a way of testing those altered propogation characteristics i.e. see who actually picks this up on low power but then again you do what you can with what you got, tx equipment aint cheap.
Anyways the images are interesting to say the least and the quality varies for said reasons, some are almost HD quality and are or nearly flawless but most aren’t. I pick up +50 per day and have collected over 70 callsigns, most are US or CAN and come in strong sometimes. The furthest was 2 images from Volano TN, Italy at 8566 km/5322 mi IN3BJS and 1 from Germany DA1GH (probably slightly further but I haven’t confirmed the city). Its going to suck when they cut the tree down but I’ll run it till then. Heres those 3 plus some nice ones, I’ll make something nice with all eventually.
So the ATV is looking good. The problem appears to be that the antenna just isn’t tuned for 423 but for 437 which makes the elements and directors at least a few centimeters short and perhaps doesn’t easily support a 6mhz bandwidth which has to do with the driven element surface area. So a new, appropriate antenna is in order. The weekly broadcast is tomorrow. Will report.
SSTV is still going for now👍. The GOES rigs are still going too. One’s been running for over a year almost nonstop (had to restart a few times over the year) and the other is approaching. This year’s hurricane season was (and is with hurricane ε) pretty active and I may at some point compile it. It’s become a ritual of clearing off the drives every so often. Will report when it exceeds 1TB.
Ah Ha! So Jim the ham ordered a matching dvbt box to mine because he’s interested in finding an easy tv decoder system for the local ham’s to watch. After a little email correspondence about the particulars of the box (included instructions are worthless) he got his working and, now that he knows how it works, has offered to program mine with 4 other channels they use (a matter of running a tuned signal into the antenna jack so the box eatablishes the appropriate channel. Otherwise it wouldn’t normally find anything unless by chance I happened to try it at the right time. The broadcast didn’t happen for said testing) So Im gonna call this one a win 
They call me the SWL/SWVer
Oh boy so the plot thickens! I attached a different antenna and it stopped working which is kind of in line with my original no signal problem. The box originally, even with a good, strong signal, didn’t work (why I contacted Jim in the first place) and then a few days later just all of a sudden started working. I thought it was because I adjusted the polarity but the box only ever shows zero signal or high 90s, no in between. I double checked the analyzer and it really should show something given how strong the signal is (about +20-25db over noise floor) but nope, nada.
After doing some research (nobody in the US uses this thing and all resources were in different languages) I found a couple people with similiar issues and its a known problem. I found a video of a guy removing two CMCs (ceramic monolithic capicitor) from inside on the dvbt part of the main board to remedy this very problem and, apparently, is the GTmedia technical support issued fix. He did it and it worked but I’d like to delve into why before I go desoldering anything just yet.
The new gaps aren’t bridged, just removed so it must be some sort of load stabilizer alleyway that just doesn’t ever seem to want to charge up all the way I suppose. That makes me suspicious of the lil rinky-dink 12v 1.5a psu. This things supposed to be able to also power a LNB and move a dish rotator so I’ll try to give it some proper juice and see what happens.
This occurred when I changed antennas so I wonder if impedance matching is just that critical. Its looking for about 75ohm which I should be roundabouts (I dont have a VNA to check) but idk
Stay tuned i.e. leave your antenna alone sometimes!
(Thanks for the post break! Was gettin long. ChileBob)
They saved me the trouble
Hmm curious… Shucks